AUTHORIZED PARTNER

Syensqo Fluorinated fluids & high-performance polymers

Galden® PFPE fluorinated fluids for two-phase immersion and direct-to-chip cooling, plus high-performance polymers for fans and thermally conductive parts. HeTone delivers Syensqo solutions across Asia with application engineering and local supply.

Syensqo products
Brand Overview

Syensqo is the specialty materials company spun off from Solvay in December 2023, headquartered in Brussels. Its Galden® PFPE perfluoropolyethers are liquid polymers built entirely from carbon, oxygen, and fluorine: non-flammable with no flash point, chemically inert, strongly dielectric, and liquid from roughly −100 °C to +290 °C across the grade range. Alongside the fluids, Ryton® PPS, KetaSpire® PEEK, and Amodel® PPA high-performance polymers serve cooling fans and thermally conductive parts.

As an authorized distributor, HeTone brings the Syensqo thermal-management portfolio to Asia. We help engineers match Galden® grades to their boiling-point and dielectric requirements, coordinate material-compatibility evaluation for immersion systems, and supply fluids, Fomblin® lubricants, and polymer grades from prototype samples through volume deployment, with Syensqo's ECHO sustainable-solutions program supporting long-term operation.

Product Series

Featured product families.

Galden® PFPE Fluorinated Fluids

Perfluoropolyether fluids for two-phase immersion and direct-to-chip cooling. No flash point and non-flammable, chemically inert, with excellent dielectric properties and stable flow behavior across a wide temperature range.

Non-flammable, no flash point

High-Performance Polymers

Ryton® PPS and KetaSpire® PEEK deliver high-temperature performance for cooling fans, while Ryton® PPS and Amodel® PPA grades enable thermally conductive polymer parts.

PPS / PEEK / PPA

Fomblin® PFPE Lubricants

Specialty lubricants built on the same carbon-oxygen-fluorine PFPE backbone as Galden®. Outstanding thermal and oxidative stability with excellent chemical inertness for demanding lubrication points.

Chemically inert PFPE
Solutions Map

Where each family goes to work.

Five application areas, three product families. Select a node to see which family carries it and what it brings.

Thermal Management

Tap a node to explore each area

High-temperature polymers Fluorinated fluids Sustainable solutions
How It Works

The fluid boils so the chip does not cook.

In two-phase immersion the electronics sit directly in a dielectric fluid. The point is not that the fluid is cold. The point is that it boils at a temperature you choose.

1

Heat reaches the fluid

Boards sit submerged. Because the fluid is dielectric and chemically inert, it can touch live components without conducting current or attacking the materials around them.

2

The fluid boils at the surface

At the hot spot the liquid changes to vapour. Boiling absorbs a large amount of heat at a nearly constant temperature, so the component is held near the fluid's boiling point instead of climbing with load.

3

Vapour condenses and returns

The vapour rises to a condenser, gives its heat to the facility water, turns back into liquid and falls. The loop needs no pump inside the tank, and the fluid is not consumed.

1 2 3 4
1Boiling at the chipThe fluid changes to vapour exactly where the heat is. 2Vapour risesHeat leaves the boards and collects at the top of the sealed tank. 3Condenser coilFacility water carries the heat out of the building. 4Condensate returnsLiquid drains back down. Nothing is consumed, and nothing is pumped through the boards.

Because the component temperature is anchored to the boiling point, choosing a grade is really choosing the temperature your hardware will run at.

It cannot catch fire

Galden® PFPE fluids have no flash point, no fire point and no autoignition point, and are Factory Mutual approved to FM 6930.

It does not conduct

Strong dielectric strength and high volume resistivity mean the fluid can sit against powered electronics without shorting them.

It leaves nothing behind

Chemically inert and residue-free, with good compatibility across metals, plastics and elastomers, so boards come out clean.

Galden® HT · Grade Selection

Pick the boiling point, not the fluid.

Nine grades run from 55 °C to 270 °C. Syensqo sets the selection rule with two numbers, and everything else follows from them.

The upper limit

Choose a fluid whose boiling point sits at least 10 °C above your highest operating temperature. That margin keeps circuit pressure down, cuts fluid loss and avoids cavitation.

The lower limit

At the cold end the fluid must still pump. The limit is where viscosity reaches 20 cP, roughly 11–12 cSt, which is what common circulation pumps can handle.

−100 −50 0 50 100 150 200 250 °C
HT55
45°
BP 55°C
HT70
60°
BP 70°C
HT80
70°
BP 80°C
HT110
100°
BP 110°C
HT135
125°
BP 135°C
HT170
160°
BP 170°C
HT200
190°
BP 200°C
HT230
220°
BP 230°C
HT270
260°
BP 270°C
Low boiling, 55 to 135 °C High boiling, 170 to 270 °C, lower evaporation loss Bars show the usable operating window. The number at the right of each bar is its upper limit.

Operating limits, boiling points and pour points from the official Galden® PFPE technical FAQ. Pour points run from −125 °C on HT55 to −66 °C on HT270. Send us your highest and lowest loop temperatures and we will shortlist the grades that cover both.

Portfolio

Five roles in the same thermal path.

The fluid is the part everyone talks about, but a cooling loop also needs parts that survive the heat, move it, and keep moving after years of running. Syensqo supplies all of it from one materials house, which means one point of qualification instead of four.

Galden® PFPE

Immersion cooling

The dielectric fluid the boards sit in. Its boiling point sets the temperature the hardware runs at.

Ryton® PPS · KetaSpire® PEEK

Cooling fans

High-temperature polymers for fan housings and blades that have to hold shape in hot air for years.

Ryton® PPS · Amodel® PPA

Thermally conductive parts

Polymer grades that carry heat instead of trapping it, so a moulded part can replace a metal one.

Fomblin® PFPE

Lubrication

Lubricants on the same inert backbone as Galden®, for bearings and seals that see heat and chemicals.

ECHO

Sustainable solutions

Syensqo’s programme for lower-footprint grades and for recovering fluid at end of service rather than losing it.

Fluorinated fluids High-performance polymers Sustainable solutions
Technical Data

Grade data, in full.

For engineers sizing a loop: the complete Galden® HT range with operating limits and pour points, plus measured properties for HT55 as a representative low-boiling grade.

Open the full grade and property tables
Galden® HT range: operating window and pour point
GradeBoiling pointUsable fromUsable toPour pointClass
HT55 55 °C -99 °C 45 °C < −125 °C Low boiling
HT70 70 °C -89 °C 60 °C < −110 °C Low boiling
HT80 80 °C -83 °C 70 °C −110 °C Low boiling
HT110 110 °C -74 °C 100 °C −100 °C Low boiling
HT135 135 °C -63 °C 125 °C −100 °C Low boiling
HT170 170 °C -44 °C 160 °C −97 °C High boiling
HT200 200 °C -33 °C 190 °C −85 °C High boiling
HT230 230 °C -19 °C 220 °C −77 °C High boiling
HT270 270 °C 11 °C 260 °C −66 °C High boiling
Galden® HT55 typical properties
PropertyValueUnit
Boiling point55°C
Pour point< −125°C
Density1.65g/cm³
Kinematic viscosity0.450cSt
Thermal conductivity0.065W/m·K
Heat of vaporization at boiling point22.0cal/g
Dielectric strength, 2.54 mm gap40kV
Volume resistivity1.0 × 1012ohm·cm
Dielectric constant1.86—
Applications

Where Syensqo products are used.

Evaluating two-phase immersion cooling with Galden® PFPE?

Send us your thermal requirements, we will recommend and validate the right material combination for your design.